Ejection Side Appearance Ejection side Control Panel LCD Panel For longer sheet, the optional long paper tray is available. Paper Curl Due to the automated slitter function, the paper path of the DC is sensitive to paper curl.
If paper curl is causing paper jams, the following are suggestions for remedying the problem: 1. Appearance Name Function Control panel Displays operations and status. Waste box Receives pieces of waste paper. Front cover Open this to remove the waste box. Separator adjustment Adjusts the distance between the separator and conveyance belt. Level adjustment knob Adjusts the elevator height. Appearance Ejection side Name Function Perforation unit Perforates parallel to the document feed direction.
Side guide Receives the processed documents. Back guide Receives the processed documents. AC inlet Connect the power cord here. Inside Name Function Double feed detection Detects double feed by the ultrasonic sensor. Option Slitter module 1,2 Cuts side margins parallel to the document feed direction. Control Panel Name Function Displays the status of the machine.
LCD panel Displays the message when an error or paper jam occurs. F key Switches to function selecting screen. Displays the JOB number currently selected. Displays the number of document sheets processed with the JOB Counter currently set. Operation of Each Part Description Paper feed section feeds the paper into the machine after separating each sheet of paper by air knife.
This is done through the operation of the air suction mechanism and the air blow duct mechanism. Page 26 Chapter 2 1 Paper Feed Section 4. Page 27 Chapter 2 1 Paper Feed Section 6. Then, the valve opens to suck up the paper. The valve is closed by the timer after the transferred paper passes through the PPS2.
Description The double feed detection sensor is provided at the ejection side of feed belt. Description The margin slitter is provided slitter 1, 2 on both sides to cut the paper along the traveling direction by means of the rotary blades. The cut-off margin is dropped into the waste box. Description Two pairs of center slitters slitter 3—6 are provided to cut the paper in the traveling direction by mean of the rotary blades arranged vertically side by side.
Page 34 Chapter 2 5 Center Slitter Section 2. Page 36 Chapter 2 6 Cutter Section 2. Description Creaser module contains the lower blade having a concave recessed section and the upper blade having a convex projected section.
The creaser unit works to crease the paper perpendicularly to its traveling direction. Operation of Each Part 1. Page 39 Chapter 2 7 Creaser Section 3. Page 40 Chapter 2 7 Creaser Section 5.
Description Stepping motors are used for activating components related to the paper cutting dimensions, paper transfer, each slitter, transversal position of the gutter. The movement of other DC motors are also controlled by the encoder attached to the motor as required. The exit tray can be set at four different heights.
Normally the tray is set at the middle height position. Upper position is to install the Card Stacker. Page Exterior Chapter 2 10 Exterior 10 Exterior 1. Description Exterior section detects the opening and closing of each cover. The machine stops immediately when the cover is opened during operations.
Operation The machine stops immediately when opening of the cover is detected during operations. Page 46 Chapter 2 11 Barcode 2. Page 47 Chapter 2 11 Barcode 3. Each of 43 character types available to CODE39 are allocated each Numeric Number to be calculated after converting them to the numeric number. Description DC automatically compensate for image drift, one Paper feed direction of the common problems on digital printers.
Take account of the possible variation in the printed position of REG marks and barcodes when they are arranged on the paper. Page Mechanism Chapter 3 Mechanism Page Open the top cover. Screw 2.
Take out the three screws, and remove the cover F. Loosen the thumbscrew, and remove the cover. Thumbscrew 5 Removing the Cover R 1. Take out the three screws, and remove the cover R. Screw Screw Screw 6 Removing the Plate 1.
Take out the six screws, and pull out the cover. Open the front cover. Take out the two screws, and remove the front cover interlock switch with the bracket. Screw Screw 3. Remove the two faston terminals. Take out the two screws, and remove the paper separation plate with the unit.
Disconnect the connector. Connector 2. Take out the two screws, and remove the shutter solenoid with the bracket. Take out the two screws, and remove the shutter solenoid.
Remove the cover F2 unit. Disconnect the connector from the motor. Remove the belt suction unit. Connector 5. Take out the two screws, and remove the feed motor. Remove the power cord plug. Take out the three screws, and remove the cover R2. Remove the plate. Take out the four screws securing the compressor.
Secured from the backside. Remove the cover R2. Disconnect the sensor connector. Connector 3. Take out the two screws, and remove the paper level sensor. Screw Screw 4. Take out one screw, and remove the shaft ASSY. Take out the nut, and remove the elevator upper limit switch with the bracket. Take out the two screws, and remove the elevator upper limit switch.
Move the elevator to the upper limit, and turn off the power. Disconnect the motor connector. Remove the banding band. Screw Connector 5. Take out one screw, and remove the sensor with the bracket.
Screw 3. Take out one screw, and remove the sensor. Disconnect the switch connector. Take out the two screws, and remove the elevator down switch with the angle.
Screw Connector 4. Take out the four screws securing the paper feed unit. Screw Screw Screw Screw 5. Disconnect the PPS1 connector, and remove the paper feed unit. Sensor installation angle is a factory setting. Screw Screw 1. Remove the cover power supply and cover R. Disconnect the connector CN8. Key Features Automatically slit, cut, crease in one pass Maximum speed of 10 sheets per minute Easy job setup and unlimited job storage via the PC Controller software Built-in CCD scanner reads barcodes and registration marks 3.
Key Challenges Manual setups on multiple devices are time-consuming Cutting applications such as business cards on a guillotine can be unproductive Changeovers between jobs are slow. Why Choose Xerox? Compatible Products Xerox award-winning digital presses can be enhanced with feeding and finishing equipment.
Thank you for your interest. A sales representative will contact you soon. Up to 20 creases per sheet. See product brochure for complete specifications. Overview Key Applications Specs Testimonials. Features Processes up to 10 sheets per minute Performs up to 6 slits, 25 cuts, and 20 creases in a single pass 80 memory settings via the control panel Optional PC Controller software, CCD scanner, and perforation unit.
Feed Capacity 3. We do all of our scoring off of it. We cut all of our business cards. It's been a blessing for us. Spot UV Coater. Perfect Binders. Guillotine Cutters.
0コメント